|
Type of vibration pick-up (contact type or non-contact type) commonly installed on a gas compressor
|
|
0
|
2091
|
October 3, 2014
|
|
Type of vibration measuring instrument is used on the compressors and the vibration measuring points
|
|
0
|
2286
|
October 3, 2014
|
|
Type of vibration pick-up (contact or non-contact type) commonly installed on a gas turbine
|
|
0
|
2002
|
October 3, 2014
|
|
Vibration measuring instrument is used on a gas turbine and the vibrations measuring points
|
|
0
|
3259
|
October 3, 2014
|
|
Why is vibration measurement very important on gas turbine and compressor
|
|
0
|
2389
|
October 3, 2014
|
|
How much is the radial vibration, if the signal measured on a DVM is 135.00mv AC
|
|
0
|
2341
|
October 3, 2014
|
|
Why an eddy probe and its probe driver is a matched pair
|
|
0
|
1921
|
October 3, 2014
|
|
Gap voltage & its setting
|
|
0
|
3394
|
October 3, 2014
|
|
Resistance of an ‘Eddy probe’
|
|
0
|
2274
|
October 3, 2014
|
|
Radial, Velocity & Acceleration
|
|
0
|
2262
|
October 3, 2014
|
|
Vibration definition
|
|
0
|
1849
|
October 3, 2014
|
|
Did bench set differ on actuators of the same size
|
|
0
|
1817
|
October 3, 2014
|
|
Bench set on a control valve actuator
|
|
0
|
2882
|
October 3, 2014
|
|
Why is there a direct and reverse action on a controller when the control valves are already having direct (air fail to close)/reverse(air fail to open) actions”
|
|
0
|
4274
|
October 3, 2014
|
|
Type of controller (P, PI, PID) is preferred for the process control loops
|
|
0
|
7852
|
October 3, 2014
|
|
Change a controller from auto to manual and vise-versa
|
|
0
|
3160
|
October 3, 2014
|
|
Bump-less transfer in a controller’s auto/manual change over
|
|
0
|
2615
|
October 3, 2014
|
|
Batch facility on a controller
|
|
0
|
2101
|
October 3, 2014
|
|
Reset action with an example
|
|
0
|
3404
|
October 3, 2014
|
|
Relation (formula) between a gain and proportional band
|
|
0
|
13019
|
October 3, 2014
|
|
Proportional band with an example
|
|
0
|
3579
|
October 3, 2014
|
|
Gap controller or ON-OFF Control
|
|
0
|
3828
|
October 3, 2014
|
|
Terms in a controller
|
|
0
|
3018
|
October 3, 2014
|
|
Controller and its application areas
|
|
0
|
3774
|
October 3, 2014
|
|
Type of orifice tapping is commonly used in P.D.O
|
|
0
|
2234
|
October 2, 2014
|
|
Burnollious Theorem
|
|
0
|
2146
|
October 2, 2014
|
|
Interface dip tape
|
|
0
|
1960
|
October 2, 2014
|
|
Convert a pressure gauge into a level gauge
|
|
0
|
2333
|
October 2, 2014
|
|
What is to be done, if a transmitter gives a maximum output , where the transmitter range (jumper) is already in maximum selection
|
|
0
|
1855
|
October 2, 2014
|
|
Application advantages of a dead weight tester and a gauge comparator
|
|
0
|
9556
|
October 2, 2014
|