# What is Signal-to-Noise Ratio (SNR) in Instrumentation Engineering Projects?

**URL:** <https://forumautomation.com/t/what-is-signal-to-noise-ratio-snr-in-instrumentation-engineering-projects/13908>\
**Category:** Industrial Automation\
**Tags:** interviewquestions\
**Created:** [February 26, 2026, 5:51am UTC](https://forumautomation.com/t/what-is-signal-to-noise-ratio-snr-in-instrumentation-engineering-projects/13908 "2026-02-26T05:51:37Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![Instrument\_Engineer](https://forumautomation.com/user_avatar/forumautomation.com/instrument_engineer/32/6734_2.png) [@Instrument\_Engineer](https://forumautomation.com/u/Instrument_Engineer)\
**Post date:** [February 26, 2026, 5:51am UTC](https://forumautomation.com/t/what-is-signal-to-noise-ratio-snr-in-instrumentation-engineering-projects/13908/1 "2026-02-26T05:51:38Z")

</div>

What is Signal-to-Noise Ratio (SNR) in Instrumentation Engineering Projects?

 ![image](https://cdn.forumautomation.com/original/2X/8/85abbf9e8900a086011fa1436b17cf822909c831.jpeg)

---

<div class="post-metadata">

**Author:** ![Sundar\_Iyalunaidu](https://forumautomation.com/user_avatar/forumautomation.com/sundar_iyalunaidu/32/7404_2.png) [@Sundar\_Iyalunaidu](https://forumautomation.com/u/Sundar_Iyalunaidu)\
**Post date:** [February 26, 2026, 1:19pm UTC](https://forumautomation.com/t/what-is-signal-to-noise-ratio-snr-in-instrumentation-engineering-projects/13908/2 "2026-02-26T13:19:41Z")

</div>

\*\*

**What is Signal-to-Noise Ratio (SNR) in Instrumentation Engineering Projects?**

\*\*

### Definition & formula

SNR quantifies how strong a desired measurement is relative to background noise.

In power terms

SNR = P\_signal / P\_noise; in decibels: SNR\_dB = 10·log10(P\_signal/P\_noise).

For amplitude ratios,

20·log10(V\_signal/V\_noise) is used.

A higher SNR means clearer, more repeatable measurements.

### Why SNR matters in plant instrumentation

- Low SNR can cause false trips, control oscillation, bad loop tuning, and wrong diagnostics.
- Common causes of noise are EMI, ground loops, cable capacitance, quantization noise, sensor thermal noise, and mechanical vibration in the process.
- Thermocouples and resistance bridges are two types of sensors that are very easy to hack.

### Design & selection guidance

- Pick sensors and transmitters that have a larger output or higher excitation when it’s safe to do so.
- Choose the A/D resolution and the noise figure of the instrument amplifier. For long runs, differential inputs and 4-20 mA loops are best.
- Use filtering (such hardware anti-alias and digital moving average), but make sure that dynamic needs are addressed.

### Field troubleshooting checklist

- Make sure the grounding is right, utilize twisted pair shields, and keep power and signal routing separate.
- Install the right surge protection and common-mode rejection devices.
- If control jitter keeps happening, you can either extend the signal span (range) or add a notch or low-pass filter at the loop level.

Write down the SNR objectives in the datasheets and check them during FAT/SAT when there is noise in the plant that is similar to what you would expect. And write down the results.
