# Flow meter sizing for orifice

**URL:** <https://forumautomation.com/t/flow-meter-sizing-for-orifice/3717>\
**Category:** Flow Measurement\
**Created:** [May 28, 2018, 3:32pm UTC](https://forumautomation.com/t/flow-meter-sizing-for-orifice/3717 "2018-05-28T15:32:49Z")\
**Posts on this page:** 1\
**Page:** 1

<div class="post-metadata">

**Author:** ![sivaranjith](https://forumautomation.com/letter_avatar_proxy/v4/letter/s/ba9def/32.png) [@sivaranjith](https://forumautomation.com/u/sivaranjith)\
**Post date:** [May 28, 2018, 3:32pm UTC](https://forumautomation.com/t/flow-meter-sizing-for-orifice/3717/1 "2018-05-28T15:32:49Z")

</div>

## What is orifice?

[**Orifice plate**](https://automationforum.co/2018/02/orifice-plates-flowmeters.html) produce a constriction in the flow channel which results in a differential pressure across the constrian. The differential pressure is measured to measure the flowrate.

## Flow rate:

 ![orifff](https://cdn.forumautomation.com/original/2X/b/be2b43cbd59f0e3f14aebd4bdbce5e8cd5ea7491.jpg)

The flow rate can be derived from the Bernoulli’s principle:

 ![bernolice](https://cdn.forumautomation.com/original/2X/4/4898c2a4a899a584038db13d98d9689fbde8152d.png)

Where prefix number represents the location 1 as the upstream and 2 as the downstream. From continuity, the velocities can be replaced by cross-sectional areas of the flow and the volumetric flow rate Q,

 ![ber2](https://cdn.forumautomation.com/original/2X/8/8f2ee75e21015ece9a4a63b54335421f052b6acf.png)

Solving for the volumetric flowrate Q gives,

 ![berr3](https://cdn.forumautomation.com/original/2X/d/dc85bbf1ba6e51e8d10cda8e810f903dcf0e1a49.png)

Since the actual flow profile at location 2 downstream of the orifice is quite complex, thereby making the effective value of A2 uncertain, the following substitution introducing a flow coefficient Cf is made, and Cd is the discharge coefficient:

 ![berr4](https://cdn.forumautomation.com/original/2X/9/9395388da87e1456df1e78652655a257da0f0621.png)

where Ao is the area of the orifice. As a result, the volumetric flow rate Q for real flows is given by the equation,

 ![berr5](https://cdn.forumautomation.com/original/2X/3/3b46cf87551280ffc2ae198fdf2721a76cae6b88.png)

The orifice plate can be made of any material, although stainless steel is the most common. The thickness of the plate used (1 / 8-1 / 2 ") is a function of line size, process temperature, pressure and differential pressure. The traditional hole is a thin circular plate (with a flange for handling) and for data), inserted into the pipeline between the two flanges of an orifice joint. This method of installation is cost-effective but requires closing the process whenever the plate is removed for maintenance or inspection. , an orifice connection allows the orifice to be removed from the process without depressurizing the line and closing the flow. In such accessories, the universal orifice plate, a circular plate with no tab, is used.

## Orifice Plate Sizing:

![ori](https://cdn.forumautomation.com/original/2X/f/f1df1a626b3297d844e58acc8e8c9d6d346f36bd.png)

QM = Maximum flow in GPM Gb = Base S.G. [(S.G. of liquid @ 60°F (Water @ 60°F = 1)] N = 5.667 for GPM D = Pipe ID in inches GF = Flowing SG of liquid @ flowing temperature (see Crane A-6) hM = Meter differential in “WC S = Orifice ratio (reference Spink pg. 167 Table 12 for corresponding β)

**Steam or Gas Orifice:**

![orr](https://cdn.forumautomation.com/original/2X/7/74d7e650f72f7b8e5c87fdcac6ba8faa13aff8bd.png)

basic steam equation:

![orrr](https://cdn.forumautomation.com/original/2X/8/8be2868ed27b3dcb1623fc4f41430b724b985a92.png)

Basic Equation Gas:

![orrr](https://cdn.forumautomation.com/original/2X/e/e6e07b55510b80238622461cfcce004ae3e16dd4.png)

SGgas=MW/29 W = Flow in lbs / hr SW = Specific Weight of vapor in lbs/ft3 = 1  Specific Volume For Steam, reference Crane A12 thru A18 (use 1/specific volume) For Gas, reference Crane A-8, column rho ‘ρ’) hM = Meter differential in “WC D = Pipe ID in inches S = Orifice ratio
